I have a PIX 515 with several public IPs, so far to create access to
internal IPs, I did something like:
access-list outside-to-Inside permit tcp host 69.y.y.y host 64.x.x.x eq www
static (inside,outside) 64.x.x.x 10.10.20.31 netmask 255.255.255.255 0 0

On dynagen ,I have configured a full mesh frame-relay ,I am using
default configuration for frame-relay.I am  able to ping every remote
router in my full mesh topology.The problem that i am facing is I am
not able to ping my serial interface IP from the router itself. I dont

    I have recently installed a Cisco 3750 on my network to give me
the ability to create VLAN's to segment my POS system from the rest of
my network.  I need to configure helper addresses in the switch to
relay DHCP from one segment to another.  I am copying the current

I am trying to get an at&t sticky ip dsl config to work for my
business class client.  I have a motorola dsl modem in front of a
cisco 1841 router.  The motorola is in bridged mode.  Here is the
config pppoe config for the 1841.

I have a 2811 and most likely will be getting an 1841.  I will need to configure both routers to handle multilink frame relay.  I have looked at both the vwic2-2mft-t1/e1 and the hwic-1fe cards to handle the WAN links.  I am leaning toward the vwic2-2mft-t1/e1 unless someone can ...

I am starting a project being required by an outside agency for network communication.  Our network presently runs on static routes allowing internal personnel in multiple locations to access internet services.  We have found that to be easier for us to maintain that using any ...

Hi all, i have read the following posting -
http://groups.google.com/group/comp.dcom.sys.cisco/msg/81d58c31469d558b
and have been trying to get this to run for the last few days, can
someone point me in the right direction please ?

hi, guys.
Recently I was trying to implement an IP PBX for my company, but I
stuck by the jitter issue.
I have a cisco 1760 router with a 10baset WIC-1ENET card, and a cisco

Iam a newb. I have to PIX 506 one in the bay and on in India. Both
were working fine until we moved them from one colocation to our main
office. Nothing has changed other than the physical location. All Ip
address on both PIXs have remained the same. I have run the debug

I have Ingenico 5100 terminals connection to AS5300 with mica modems.
When terminals are set for 2400 and I have
Code:
modemcap entry

I've put together 2 IP Subnetting Books  to help cut through the
clutter and confusion of subnetting.
It's hard work, but it's work that pay's off on the Job.
Once you master it, it is just practice and speed.

Is it possible to encrypt all TCP or IP packets going out to a
corporate public virtual network without using IPsec. All routers
going on the corporate VPN would hardcode this way of doing things (no
policy negotiation).

How can I measure encryption performance on my PIX's?
We have a couple very old 506E at remote locations connecting to a PIX 515E
here and performance is not up to snuff.
I am looking at my VPN devices and if the encryption I am asking it to

I am new with FWSM. I am try to implement with routed mode in multiple
context. Currently the traffic seems totally bypased the firewall, what am
I missing here. Thanks in advance. Here is the basic design.
6506 MSFC

I am having an issue with 20 of these units that came in because I
cannot get the unit to do the "clear lwapp private-config" command
because it is disabled. I am not sure how to go around the unit.
Websites are telling me that I have to do it through a Controller. I