I'm trying to configure two Cisco 2621 routers for dial backup. Main
interface is Fastethernet 0/0. Backup is dialer1. When router
TSFSDINLINRT1 int fast 0/0 goes down dialer 1 come up but there is no
dial action. I can dial trough manually so I know the phone circuits

We have a small office with 30 PCs and they are connected to us via
half of a T1 with Cisco2621's on either side.  As of about 9:30 this
morning the have been getting bumped from the two programs they access
from here.  We aren't having the problem.  It comes and goes, and

Behind one of my PIX's (a 525 failover pair) I am having trouble browsing
certain websites for example "www.cnn.com" and the "Microsoft Update" site
but "www.foxnews.com" and "Windows Update" sites work fine.
Anyone seen this issue before?

I have a webserver in inside network with IP: 192.168.1.99 . The
outside IP of PIX 501 is 71.155.211.233 and inside IP of PIX 501 is
192.168.1.1 . what to do if I want my webserver visible from public
internet? I need HTTP://71.155.211.233 will be directed to my website

Can anybody help? I need to setup "inside to inside NAT" as described
here:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5413/prod_release_note09186a00
80457818.html#wp67645
I'm running 12.4 on a Cisco 837, and I know this feature is supported

I have two sites connected through WWW(routerA below) and am trying to
configure HSRP for redundancy at both sites by subscribing
DSL(routerB).
My current layout:

I have two PIX 501s and they were connected via a vpn. All of a sudden
the circuit dropped and after rebooting both devices, I ahve not been
able to reestablish the VPN. I changed the PRE-SHARE key on both and
changed the transform sets, but no change. Once someone gave me a

I want to establish a VPN tunnel between 2 PIX515E, a site-to-site VPN.
I have used the wizard of the PDM.
First, the tunnel seems ok : I can ping hosts on remote site, telnet,
etc.

I have an existing wireless network utilizing an Aironet 350 Bridge and
two remote locations connected to the bridge with Aironet 350 Workgroup
bridges. One location has outgrown the WGB's limit of 8 clients and I
need to replace it. I have checked the cisco website and phoned their

we have quite a few cisco access points, mostly the 1100 series.
I was wondering the recommended solution for monitoring and maintaining the
access points.
I have downloaded different packages to try that allow me to monitor the

These days I seem to find myself waking up with googles under my eyes
instead of sleet.
I've got a Cisco 675 that I have been trying to figure out how to parse
and log bi-directional traffic thru the wan. I am able to get the units

How to restore the power in rps ....with rebooting the switch or any
device connected with it .. can any one, please  help me ..
Rajinder

Is any VLANs limitation on Cisco 1801 or Cisco 1841. I have small
project where I want use Cisco 1801 (preffered) or 1841 to
inter-vlan routing+CAR QoS between about 50 VLANs.
What kind of software license I need to use VLANs on 18xx?

Which model of Cisco router (not Linksys) would work best with a cable
modem?  Is it possible?

Consider this statement from a PIX white paper found online:
A packet is entering an interface and PIX evaluates the security level
for the source and destination interfaces. A low-to-high is allowed
only if there is an access-list/conduit that allows the connection and