Hello dear newsgroup participants,
following question:
CheckHeap and CheckStack (this as part of per-minute jobs)
run on many routers. Following questions: Does someone here

Shortly, our company will be changing ISP which also means that we
will be assigned a new IP range. Our current IP range is not provider
independent so however the outcome, we'll need to make some changes in
our firewalls.

What's the easist way to advertise only a default route to a remote
router?
I would prefer to use BGP, but am able to use EIGRP instead if that is
more preferred.

I would like to know if I can configure static commands with
overlapping addresses and it works.  For e.g. if I have an address that
is already covered in a net static statement like:
static (inside,outside) 192.168.10.0 192.168.10.0 netmask 255.255.255.0

i'm just having trouble setting up an etherchannel with diffrent hardware
speeds, simulating the same speed. i tested this already in following lab:
Cat 3750 gi0/0/1 and gi0/0/2 both at 100MBit in channelgroup 1 running as
trunk port dot1q (portchan mode auto)

I have a Cisco VPN concentrator 3000 and I am trying to bring up a
tunnell to a pix that has a DHCP outside address is this possible I set
my config parameters in the lan to lan tunnel to originate only and ip
25.0.0.0 and this didn't do it.  I can set the peer address to the

I just got my hands on a Catalyst 5500 switch - and I've been asked to
upgrade it with more ports.
The chassis has 13 slots, where slot 1 & 2 has been used for Supervisor II
modules ... Another slot is used for the Router (layer 3) module .. Besides

Hi.  I have what I think is a pretty basic question.
We have a T1 to our ISP.  The router that the T1 connects to is a Cisco
1700.  Inside that router, we have our firewall - a PIX 515, and our
network is on the other side.  We'd like to put another network inside

I have a single Cisco 2950T with 24 100 Mb ports and a couple of 1 Gb.
"uplink" ports.
I have a small network (15 devices) and one switch is enough for now.
I'd like to upgrade on of my Servers to a 1 Gb. NIC and connect it to

Hi.  I have what I think is a pretty basic question.
We have a T1 to our ISP.  The router that the T1 connects to is a Cisco
1700.  Inside that router, we have our firewall - a PIX 515, and our
network is on the other side.  We'd like to put another network inside

I've come to a stand still with my first simple IPSEC tunnel­ and I
was
looking for a 2 opinion. I have 2 bridged DSL circuits termi­nating on
2610 with an ether module (System image file is

IS THERE SOMEBODY THAT COULD HELP ME? I AM PLANING TO GET CCNA, AND A
FREND OF MINE GAVE ME AWAY A CISCO 2502 ROUTER WIHT A CONSOLE CABLE
WIHT A DB9 AT ONE END AND A RJ-45 AT THE OTHER END, MY QUESTION IS,
WHAT CAN I DO TO GET ACCESS TO THE CISCO ACL, THROUGH MY PC, TO SEE

i have router with one configuration, and
i need make another one, but machine is remotly
administarted and i want to backup myself
can i make two startup_scripts and switch

hi @all,
when i point my browser to my routers ip - enter the password and select
the language for the web start...the java applet is running some
checks...but doesn't come to an end. it seems the process for checking

Hi...
I have 2 3640 routers with 2x2MB circuits connecting them.  I am using
1 of the ccts for specific traffic, and the other for everything else.
(These are not the real addresses)