Router A BGP Peers with an upstream.
Router A and Router B run HSRP for each other and BGP peer with each other
If router A fails then router B will get A's IP and the upstream will try to establish a BGP session with router B, BUT unless router B has the relevant BGP config then ...

Trying to find
12.2(3)T
for my Cisco 2621 and for the life of me, I cannot, Cisco
website is so convoluted! can someone help me out?

ABR router with area 0 and 1 configured, if the OSPF database has
information about a network learnt from area 1 and from area 0 (interarea)
which one goes in the route table, what are the OSPF rules for entering
information into the router table?

We had a situation as follows:  We set up our wireless network in a
camp with and had it going for a while, a few days, meanwhile another
group tried to set up their own wireless setup - with different ip
addresses and different networks i believe - and they could not start

using Microsoft IAS in active directory domain as Radius server.  A policy I
have set up for admins is to get privilege level 15 when they log in, this
works fine when they telnet in but when you go via the console they only get
privilege level 1 - is this correct or I have forgot ...

Users are complaining about static and echos on their Cisco 7940s and
7960s.  I'm new to this VoiP stuff so I'm at a loss.  I know its a broad
question.  Any ideas?
Thanks.

I have a Cisco 2651 xm router with 2 interfaces. First, the external,
mapped to the ip address allocated by the provider, corresponding to
my domain, let's say www.x.com. The other one, internal, with an ip of
10.1.1.1. My LAN has addressess in the pool 10.1.1.0/24. I have also

whats the best ? what do you use ? I need the application to follow
convention with regards to its drawings etc.. i.e. a router looking like a
3-d cylindrical object with the 4 arrows on it!
The reason I ask, is because i'm using VISIO 2003, and this useless piece of

I have a Firewall cisco pix 515e with 6.2 OS and i try to copy the
configuration to tftp server 10.0.0.2 using the command "write net"
but it leaves the error to me "timed out attemping to connect"
[failed].

I am looking for a tool to track MAC addresses on a Cisco network.
The main purpose is to find devices which are not known to us and
which people connect to our network.
We use Catalyst 2924XL, 2950C, 3524XL and 3550 running IOS but also

I was going to try and setup a Cisco 837 ADSL router for one of our
branch offices.  Currently they have one PC with a DSL modem.  They
are expanding to 4 PC's, so we were going to through in the 837 to
replace the DSL modem, get the 4 PC's plugged into it, we want the 837

Can I have more than one IP address mapped to the external interface of a
PIX 501?
cheers
Dave

Hello Group,
Is it possible to create a DMZ with 2 PIX 501 Firewalls and then
sandwich a public web server between them?  Internet--Pix1---web
server---Pix2---LAN.

Soory if this is a way of question. I want to add a hardware firewall between
my pc and internet. I use an internal modem with my aol. I can only have dial
up as broadband etc are not an option. I have two pc lnetworked. I only use one
pc at a time so wont be accesing the internet ...

i've a problem ;-) so i need a feature like interface tracking from hsrp but without hsrp.
i need the following:
i have 2 router (cisco 2621) and i've two interfaces on each router. interface 0/0 is the uplink to my provider. i've two subnet's in which each router is connected ...