Dear All .....  Are those here who use Win'98/SE
and have Pentium-4 motherboards that use the
"SiS" chipsets able to get USB2 enabled and
fuctional?

Is there anything (bad) I should know?
I am not a big overclocking nut, but I would like to be fairly sure I can
get 210MHz or so out of my Barton 3200+. Will that be a problem, do you
think? I know that will mean running my PCI bus at 35MHz and AGP at 70MHz,

F**k me dead!
After futzing with this mobo for a month, reseating the cpu fixed a booting
problem?  It was seated in the socket like it should and it would hang on
the memory diagnostic during the POST.  Today for no real reason other than

Hi all does this mb have a firewire header on it or just the external
firewire socket? have seen differing reports!!
Thanks
PS would you recommend this board in general for an Athlon 64 build?

I have just installed a Maxtor Plus 9 250gb SATA hard disk into my
system.  However, I cannot get my computer to recognize it at all.  In
other words it does not appear in the BIOS (Serial_Ch0 and 1 say not
installed).  It is not recognized by Windows XP Pro either, neither in

Will it hurt anything except performance to run the PCI bus speed at 31-32?
I am slowly raising the FSB a little at a time. But I don't know if I will
be able to get the PCI speed up to 33 due to the 1/5 divider.

I have built the following pc:
MSI neo2 865pe pentium 4
Sound Blaster Sound Card - Audigy 2
The problem I am having is during post. After the IDE & CDROM Drives

I own a KT6-LSR. I watch alot of movies and i have a home theater set up in
the same room as the pc. My first plan was to buy the kt6-lsr, and by the
s-bracket afterwards. But i have come to find that its pretty hard to find
the bracket anywhere.

   I have a KT3 Ultra 1 and I would like to put the fastest processor
possible on it. Officially, it is the XP2600+ @ 266, but some persons seem
to run a xp3000+ on it without problem (or on a Ultra 1 ARU). So what to
think ? Is it just that the processor isn't used at the full ...

Hey i got a a questions for anyone who wants to answer!
I am running a MSI Neo2 Fisr2 with a pentium 4 3.0ghz 800FSB! Right
now i am running it at 200mhz, or so says my bios and my corecenter. I
want to increase the FSB on my CPU for max performance, but in my bios

Currently have a K7TPro2 board, 1800+ and 512 megs PC2100 RAM
got to replace it all...
what board & chip you recommend?  best bang for the buck?

   I would like to know if I am the only with the following problems:
            Booting with the 82547EI LAN enabled
            Installing the USB2 drivers
   I've tried everything short of reinstalling Windows. I'd appreciate

Is there anything (bad) I should know?
I am not a big overclocking nut, but I would like to be fairly sure I can
get 210MHz or so out of my Barton 3200+. Will that be a problem, do you
think? I know that will mean running my PCI bus at 35MHz and AGP at 70MHz,

I have MSI 848P Neo mobo (Intel's chipset). Processor is Pentium 4
2,8.
The problem is, that when I connect my Agenie Pro 128Mb USB-memory,
whole computer hangs and I must reset the computer.

I've tried many different combinations of multipliers and FSB, nothing works.
The Bios is AW 3.6 which is the latest and greatest.
At boot-up I get processor unknown @ 1533 MGH.
According to the specs at MSI this MB should handle AMD Athlon 2600+