while the system (P4 3,2 - 1024 MB TwinMos) is booting, no pci cards are
recognized. I´ve tried to put them in different slots but it´s always the
same. Sometimes the cards were recognized - sometimes not. I´ve set the bios
to defaults - get the newest bios F8 - cleaned the contacts ...

I have a 7n400 pro2  and I want to add a Game port.
I see in the book that there are pins on the MB for a Game port .But Mb's
used to come with the cable and connections None came in my MB box, does
that mean I now have to go out and buy a special Card or a special Game port

I built my own computer some time ago now and at that time I selected the
8hixp board.   I could not afford a lot of memory so stuck in two sticks of
128 x 16 - 4/128 non-ecc memory.   I would now like to upgrade the amount of
memory by adding two further sticks of 128.  I am having ...

Updating from a GA-8IEXP Rev 2  to a GA-8I875 Ultra
and to a P4  2.4C..
What do I remove in the Register so that XP will re-detect the new Hardware..?
Thanks

Re Bios version 10, where can I access it?
I recently tried to flash upgrade using the CD which came with the MB when I
originally bought it 2 years or so ago. I remember finding this so much
easier than a previous method.

A friend of mine is trying to put a 2400+ in my GA-7DXR.  It previously had
a 1.333 thunderbird in it.  The system won't power up now.  We've tried
different power supplies, another cpu (900 mhz 200 FSB), clearing the CMOS,
taking out the battery, and replacing the power switch.  ...

I Own 8KNXP Rev 2 with BIOS Rev FB. I recently attempted an update to
FE (or FD) using QFlash. I got an "BIOS ID Check Error". If I flash
the FB version from Gigabyte site it works well (same as my original
FB BIOS).

Particularly the 7NNXP AMD board. To be honest, I'm new to this bit of kit
and therefore had a from the computer shop install it. To be fair to him he
installed it on the basis of not adding all the components until we knew
otherwise.

My Local dealer has now confirmed  that the current stock here of Gigabyte
GA-8I875 Ultra  boards are Rev 2 with a Yellow mounting bracket  as per the
bottom Full Pic..
Prescott Info.

I have a Gigabyte GA-7VRXP and I'm trying to figure out what the fastest
processor is that can be put on it...
Its a Socket A board with 200/266 MHz FSB.  VIA KT333 Memory Controller.
It says it supports from 1.4 GHz and up.  BUT, where does it STOP?

I have a newly built computer with a Gigabyte GA-7N 400L motherboard.
The problem is that I get spurious sound effects corresponding with normal
activities. The mouse wheel creates a hissing noise and even opening a
window creates a noise in tune with the action. Is this a known ...

I'm hoping someone can assist with a booting issue that I have with my IHXP.
I am currently running XP Pro off of a raid 0 array on the on-board promise
controller.  It works fine.   I also have an Adaptec 29160 with a scsi drive
attached with an install of win98 and MDK9.1.  WHen I ...

I have the latesest F13(i believe) bios installed and have recently
discovered that my processor (XP 1800) has kicked the bucket. I am
looking into getting a 2600 Barton 333FSB and overclocking a bit to
match the Tbred clock speed. Will this be possible on the 7VAXP

I want to use  Wacom Graphics tablet with the 8KNXP and the v6 BIOS.
In this situation shouls USB Mouse in the BIOS be enabled or disabled
(default is disabled)?  It is a USB device but has its own driver.
Howard

Hi, I have an issue with this board running stable at stock settings.
I just got it up and running but it is unstable with RAM at 400MHz. I
am using BIOS F8b, a 2.6C P4, Kingston HyperX 3500 512 stick, WD 120GB
SATA drive, ATI AIW 7500 video, and Antec 380W True power in a Sonata