ok--i finally succeeded in setting up what i think is a proper raid 0
configuration, but i'm not sure:
-2 120 gb SATA baracudas. at boot up, the intel raid configurator
shows them as both a part of a raid 0 array

P4C 2.8 HT w/ a 8KNXP with the DPS + 4 HDD 2 optical drives, GeForce FX 5600
, floppy & Zip dr?
I have a 350 Watt PS & it doesn't seem to have enough juice to boot up the
system.

I recently purchased the above mobo and set up a Raid 0 (Stripe) using
2 ATA 133 60gb drives.
Using Sisoft benchmark the speed of this drive is returning 27,000,
which is well below what it should be (probably close to double)

Here the problem:
2 hd on ide/raid controller promise in ide-mode
Maxtor   80GB Ata133
Maxtor 160GB Ata133

Hi, I have a GA-7VA motherboard running a XP 2400 with 512 Ram.  I have a
nice ventilated case, and was wondering about a case fan to keep things
cool.  The following temperature reading I have now:
CPU:  Idle = 53 degrees  Full load = 62 degrees

Hi,
Does anyone have experience connecting LianLi PC6070 case's 2 front USB
ports to the GA-8KNXP mobo?
The mobo diagram is not very clear to me:

Based on all of the glowing reviews I was a day away from ordering
Abit's IC7 when I stumbled on their forum and found they had a serious
issue with their onboard sound.  So now I'm looking again.  These two
Gigabyte boards also seem to be very well rated.  I have some questions:

Where, on the 'new look' Gigabyte web-site, do I find the latest version of
@Bios?
It doesn't seem to be under any of the headings and sub-headings.
Need to upgrade my BIOS after the PS/2 socket shorted and reverted M/B to

Hi I am running a 8KNXP  F6 Bios with a P4 3ghz 800fsb cpu and 4x512 PC3200
Kingston ram,
Windows XP Pro with all the latest patches Gigabyte GV-R98P128D graphics
card, 2x40GB Western Digital

When I insert a cd into one of my drives I get a blue screen saying Stop
0x000000B8 Error, A wait operation, attach process, or yield was attempted
from a DPC routine.
I have searched google and tried Microsoft's website but this stop

I have an GA-8KNXP, Is it possible to put a DVD rewritable drive on ide3 and
say a cd writer on ide4, if it is possible what do I have to do to set it
up, i.e. bios settings, install drivers etc. I am very new to this so the
more information the better, thanks in advance.

Checking prices on memory for PC3200, I notice both Corsair and
Kingston  "extreme memory" modules with speeds of 200mhz and above
have higher latencies than PC2700/3000.  PC2700/3000 is as low as
2-2-2-5 but PC3200 and above is no lower than 2-3-2-6.

Hi there ppl
I have an old p3 450 on a Gigabyte 6BXC and im trying to get a new 160
GB hard disk to run on it. The last BIOS only supports HD up to 75
GB. Is there _any_ way to make this hard disk work on that board? (the

Running a SmartUPS420net, (420VA/260W) on a new 8KNXP w 1GB, 3drives, couple
of optical drives.  UPS came from an older system and worked fine.
The UPS was well-behaived until I did a render task that pegged the
processor(s).  At that time if I had a window open vs minimized the USP

I have 2 Corsair PC 2700 333Mhz 256 Mb ram banks in slots 1 and 3 of my
7n400 Pro 2 board but the maximum speed I can set them to is 266 Mhz. When I
set the bios (latest version) to adjust memory "by SPD", Windows 2000 (with
SP 4) gives me the blue screen of death on boot up.