please I seek all drivers for mothercard ECS K7VZA ( KT133)
with integrate sound
tanks
gerard

Does anyone have any ideas if this combo will work? I'm thinking of putting two
sticks of PC150 of differing sizes (512 and 256 Corsair) and manufacturers,
would this also cause problems? The CPU would be a Duron-Morgan 1300.
-Bill (remove "botizer" to reply via email)

Was working fine 2 days ago, now it won't boot.  It powers up, but I get no
beep.  Then it flashes the HDD, DVD and CD lights alternately.
No video signal.  I swapped video cards with a known working one, still
nothing.

I just read in a post that the K7S5A pro board doesnt work with the
AMD XP Barton cpu's.  I just bought this board and the 2500 333fsb
Barton, I know the board is only 266 but I thought it would work ok.
The only issue I had was trying to get the bios setting to 166mhtz,

I have a ati radeon 9200 SE video card. I have not been able to get the fast
write to be enabled y? I went through bios and display properties still wont
do it.

Hey all,
   I was referred to this site for some expert advice.  I recently
bought a K7VTA3 V8 mobo with a AMDXP2000+ combo from Fry's...  After
sorting out all the problems, I did a clean install of WinXP... Then

I tried to upgrade from Windows ME to Windows XP Pro... the motherboard is K7S5A Pro. It starts out ok... but then it
states some nonsense about not having the Via and or SIS drivers and quits the install.. Of course I have the drivers ..
but I am stuck. I even doubt a clear ...

   Has anyone had unusually good or bad experiences with the ECS K7VTA3
version 8.0C?  What are its pros and cons in terms of both overclocking and
durability?  Thanks, sdlomi

The computer in question has a K7S5A board with a Voodoo3 2000 AGP card.
When I first built the computer, it worked fine for a few months.  Now,
sometimes the computer will boot with the card, and sometimes I get beeps.
The board works fine with an old Matrox card, and sometimes it ...

Will PC3200 work with my K7S5A ver 3?
I'm about to upgrade to 1Gb and wanted to know whether it will work?
Am I right in thinking that it will only support upto 512Mb sticks and not
1Gb?

I recently rebuilt a budget system using a ECS K7VTA3 v8.0, Athlon XP 2500+,
512MB PC2700 memory.   (The MB, processor, and memory combined only cost
$129 at Frys - I thought that was a great deal.)   In general the MB
replacement went smoothly and Win XP Pro installed fine.   The ...

   I just looked at ECS site and could not see differences between the 5.0
and 8.0 versions except that I think one of the mobos had 3 ram slots and
the other only 2.  I think it was the 8.0 that only had 2 ram slots.
   Are there substantial differences?  Is either one suitable ...

I just baught a new ECS K7S5A Pro motherboard for my machine.  I boot of a
adaptec 29160 scsi card.  Once the system posts it will hang for exactly 65
seconds before the OS starts.  Once the OS starts everything works
perfectly.

Hi All: I have a very annoying problem trying to get my USB ports to
work. If I enable USB in the BIOS setup the computer locks up after
WIndows (XP) starts. I have tried clearing the CMOS, upgrading the
BIOS, and even tried installing a PCI USB controller card (it too

My L4VXA2 is locking up intermittantly.  Any thoughts on how to begin to
figure the probelm out?